Loading…
You're signed in. Before continuing, please confirm you are 21 or older and buying for laboratory research use only (RUO). Products are not for human or veterinary consumption and have not been evaluated by the FDA.
You must be 21 years of age or older to view our products. Access has been blocked on this device.
Welcome to Crux Peptides
Use this code at checkout. Applies to your whole order.
Both are sterile, nonpyrogenic water. Bacteriostatic water made to the USP standard also contains 0.9% benzyl alcohol, a preservative that slows the growth of bacteria introduced when the vial is entered, so one vial can be used several times. Sterile water has no preservative, so each vial is meant for a single use and the remainder is discarded.
| Bacteriostatic water | Sterile water | |
|---|---|---|
| What it contains | Sterile water with 0.9% (9 mg/mL) benzyl alcohol | Sterile water with no preservative and no added buffer |
| Vial type | Multi-use vial | Single-use vial |
| After the first entry | Can be entered again; date the vial and follow the label’s discard time (28 days is a common convention) | Discard the unused portion |
| Name on the label | Bacteriostatic Water for Injection, USP | Sterile Water for Injection, USP |
| Typical lab use | Reconstituting a compound that will be drawn from more than once | One-time preparations, and methods that must avoid benzyl alcohol |
Bacteriostatic means the solution holds back the growth of bacteria rather than killing everything in it. The 0.9% benzyl alcohol limits growth of organisms that can get in each time a needle or pipette tip goes through the stopper. It does not make a contaminated vial sterile again, so aseptic technique still matters: wipe the stopper with 70% isopropyl alcohol before each entry and use a new sterile needle or tip every time.
Start with the compound’s own documentation. The supplier datasheet or certificate of analysis usually names a recommended solvent, and that recommendation wins over any general rule.
When the documentation leaves the choice open, these points usually decide it:
Bacteriostatic 0.9% sodium chloride is saline with the same 0.9% benzyl alcohol preservative. The added salt changes the ionic strength of the solution, which can lower the solubility of some peptides or interfere with a method, so use saline only when your protocol calls for it. “Reconstitution solution” is a general term, and vials sold under that name may contain sterile water, bacteriostatic water or something else. Read the label to see what you have.
The USP standard for bacteriostatic water is 0.9% benzyl alcohol, but check the label on your vial for the preservative and its concentration before you use it. Unopened vials of both are typically stored at controlled room temperature, 20 to 25 °C (68 to 77 °F), away from direct light. Check the manufacturer’s label for the exact range.
After the first entry into a bacteriostatic water vial, write the date on it and follow the label’s discard time. Discard any vial, opened or not, that looks cloudy, contains particles or has a damaged seal. A sterile water vial is single-use, so discard whatever is left once you have drawn what you need.
For storing the peptide itself, before and after it is dissolved, see our peptide storage and handling guide.
For a preparation that is used right away, yes. Without a preservative, a sterile water vial that is entered several times can pick up contamination between uses, so treat each sterile water vial as single-use.
Follow the manufacturer’s label. A widely used convention for multi-use vials, from USP General Chapter <797>, is to discard them 28 days after the first puncture unless the manufacturer states otherwise.
No. Distilled and deionized water are purified but are not sold sterile and contain no preservative. Sterile water and bacteriostatic water are sterilized and sealed in vials, and bacteriostatic water adds 0.9% benzyl alcohol.
Unopened vials are usually labeled for room temperature, 20 to 25 °C (68 to 77 °F). Follow the label for opened vials. The temperature of the peptide solution you make with it is a separate question, covered in the storage guide.
Yes. Bacteriostatic water is available in 3 mL and 10 mL vials, from $8, and ships to addresses in the United States. Check the vial label for its preservative and concentration. Free shipping applies to orders over $150.
Crux Peptides products are for laboratory and in-vitro research use only. They are not for human or veterinary use. This guide covers laboratory handling and is not medical advice.
We use cookies to measure our website and the performance of our ads. You can accept or reject them; the site works either way. Privacy policy